Balaji Techno Traders

Fevicol ANR 243

Medium-strength locking and sealing compound for threaded nuts, bolts, small screws, and small diameter studs which require ease of reopening

Fevicol ANR 243
- Single component
- Solventless
- Fills gaps up to 0.25 mm
- Long shelf life
- Good resistance to all usual fluids, gases, and chemicals
- Temperature resistance up to 150° C
- Appearance: Blue liquid
- Viscosity: 25 P
- Setting time: 15 minutes
- Breakaway torque: 250 kgf.cm
- Prevailing torque: 150 kgf.cm
Fevicol ANR 270

Used in rotor to shafts in fractional and sub fractional horsepower motors. Suitable for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where maximum strength is required. Apt for lock bushings and sleeves in housings on shafts

Fevicol ANR 270
- Single component
- High strength
- Solventless
- Suitable for plated/passive surfaces
- Fills gaps up to 0.25 mm
- Long shelf life
- Good resistance to all usual fluids, gases and chemicals
- Temperature resistance up to 150° C
- Prevents thread corrosion
- Appearance: Green liquid
- Specific gravity: 1.08
- Viscosity: 500 - 800 cP
- Breakaway torque: 19 to 39 N.m
- Maximum prevailing torque: 45 N.m
- Compressive shear strength: minimum 9.2 N/mm²
Fevicol ANR 574

Recommended for use as a fast setting flange sealant for all types of machineries such as air compressors, pumps, and gear boxes of heavy duty cranes, oil sumps etc. especially on rigid and semi-rigid iron and steel flanges. Used in oil filter as a sealant to prevent oil leakage. Also used on pipe flanges

Fevicol ANR 574
- Single component
- Fast curing
- Solventless
- Ease of disassembly
- Fills gaps up to 0.50 mm
- Long shelf life
- Good resistance to all usual fluids, gases, and chemicals
- Temperature resistance up to 200° C
- Appearance: Orange opaque viscous paste
- Viscosity: 300 P
- Set time: 15 minutes
- Break-loose torque: 140 kg.cm
- Prevailing torque: 20 kg.cm
Fevicol ANR 638

Retaining cylindrical parts such as roller bearings, bushes, gears, pulleys, locking bushings, and sleeves into housing and shafts in the automobile and engineering industries. To retain bush in timing cover (oil impregnated bushings into housings), speedometer drive housing etc.

Fevicol ANR 638
- Single component
- Fast curing
- Prevents loosening and leakage from shock and vibration
- Excellent resistance to dynamic, axial, and radial loads
- Good resistance to all usual fluids, oils, gases, and chemicals
- Temperature resistance: 55 to -55° C
- Appearance: Green liquid
- Viscosity: 2200 to 2700 cP
- Set time: 5 to 10 minutes
- Break-loose torque: 350 to 450 kgf.cm
- Prevailing torque: 100 to 200 kgf.cm
- Static shear strength: 200 to 300 kg/cm²
Fevikwik 203

Suitable for bonding plastic, metal, rubber components. Can be used to lock components which are already assembled. The typical application in molded furniture, sign Boards.

Fevikwik 203
- Colorless
- Solventless
- Fast setting
- Ease of application
- Good penetration in close fitting parts
- Appearance: Clear transparent liquid
- Shelf Life : 9 months under dry and cool (<25 oC) storing Condition
- Operating Temp : – 40 °C to +80 °C
- Specific Gravity: 1.06 approx
- Viscosity @ 25°C Approx. 2-5 cps
Fevikwik 702

Apt for bonding name plates to plastic body equipment. Perfect for assembling plastic-knobs. Ideal for fixing PVC/rubber gaskets to metal parts in filters

Fevikwik 702
- Single component
- Multipurpose adhesive
- High strength
- Good resistance to motor oil, gasoline, and alcohols
- Appearance: Clear transparent liquid
- Viscosity: Approximately 80 to 120 cP
- Gap fill: 0.15 mm
- Flash point: Minimum 85° C
- Shelf life: 9 months
- Specific gravity: 1.06
- Shear strength MS to MS: 100 kg/cm²
- Operating temperature: -40 to 80° C
- Full cure time: 24 hours
Feviseal Neutral Pro

Feviseal Neutral Pro 280ml is a silicone sealant, neutral-cure, used for sealing joints and gaps in various applications, interior and exterior. Adheres to glass, ceramics, metals, and plastics

Feviseal Neutral Pro
- A highly flexible, durable and odourless neutral silicone sealant
- Sealing windows & doors
- Residential decoration filling & sealing
- Frame & floor filling
- ACP bonding
- Mirror bonding
M Seal Epoxy

Sealing of leakage/cracks in metal fabrications, industrial vessels, boilers, hulls of ships, boats and trawlers. Sealing water supply mains, storage tanks, concrete sewer pipes, heat exchanger coils, etc. Sealing blowholes, cracks, and leakage in ferrous and non-ferrous casting, pumps and mould boxes etc. Sealing holes/cracks in wooden and metal patterns. Repairing of damaged internal threads of various types of machine pumps. Sealing cracks in casings of meters/gear-box etc. Repairing heat exchangers and condensers. Tank linings and chutes, Agitator Shafts, Slurry Lines, Spiral Classifiers. Resurfacing and repairing rudders and pintel housings. Repairing of cooling pump impellers & Butterfly valves

M Seal Epoxy
- Cures in 10 to 20 minutes at room temperature
- Co-centric stick – Convenient to use, cut required quantity and use
- Best for salty and humid environments, heat resistant up to 120C
- Cured product can be drilled, filed, tapped, machined, cut and then painted
- Appearance ( Mix): Grey putty
- Components : Two Components
- Mix Ratio by Volume – Resin : Hardener:: 1:1 w/w and 1:1 v/v
- Cure : Room temperature
M Seal Red RTV Silicone Sealant Gasket Maker

M-SEAL RED RTV Silicone Sealant finds application in Automobile, Electrical & all types engineering industries. Primarily used for Gasketing in hot engines of modern cars. Also used in refrigeration units, fixing screw-less brackets or nameplates, sealing windows in oven doors, gas appliances, flanged pipe joints, marine cabins and windows. Used to make formed-in-place or in-situ gasket for gearbox, compressors, pumps etc.

M Seal Red RTV Silicone Sealant Gasket Maker
- APPLICATION AREA: Automobile, Electrical & engineering industries
- Formed-in-place / in-situ gasket
PIDISEAL 3P

Sealing cracks around windows, ducts, fixtures. Sealing leaks in gutters, ducts, piping, and downspouts. Formation of gaskets for gear boxes, machine cover gauges, thermostat housing to prevent oil and water leaks. Protection of glass meter covers from vibration

PIDISEAL 3P
- Single component
- Ease of application
- Fast curing at ambient
- Excellent resistance to weathering, vibration, moisture
- Good electrical insulation
- Can be applied on vertical and overhead joints
- High temperature resistance
- Excellent flexibility
- Colour: Translucent white
- Flow/slag at ambient: Nil
- Density: 1.03 gm/cm³
- Tack free time: 15 minutes
- Full curing time: 24 hours for bead of 2 mm thickness and width
- Hardness shore A after 7 days cure: 22
- Elongation at break: Minimum 250%
- Paintability: Non paintable
- Temperature resistance: -40 to 240° C
RUSTOLENE

Cleans surface from rust, grease, oil, dirxt, carbon deposits & other sticky materials. Displaces moisture from metal surfaces, car delco, spark plug, battery terminal. Penetrates & loosens rusted nut-bolts & jammed assembly

RUSTOLENE
- Cleans rust, grease, oil, carbon deposits
- Displaces moisture from metal surfaces
- Penetrates and loosens rusted nut-bolts and jammed assemblies
SYNTHEIC RUBBER AHESIVE

Synthetic rubbers manufactured using petrochemical sources in chemical plants, factories and laboratories

SYNTHEIC RUBBER AHESIVE
- Common types include styrene butadiene (SBR)
- Nitrile rubber (NBR)
- Polychloroprene (Neoprene)
- Silicones
USPRO

Sealant for cable entries from walls, electric switchboards, panel boards. Telecom towers and power supply panel boards. Making model, sand plate, repair of show board in advertising field. Sealant in speech room and broadcasting studio for insulation and absorption of sound. Daily maintenance like repairing of hole or gap in wall brick or earth brick. Mending hole in water pipe. Packing valuable and fragile goods to provide shock resistance

USPRO
- Easy to use like DIY
- Automatic spray
- Automatic expansion helps in filling all gaps
- Air humidity cure mechanism
- No pre treatment required for surface
- Good viscosity (especially on wet surface)
- Base: Polyurethane
- Density: 15 kg/m3 to 30 kg/m3
- Temperature resistance of cured foam: 35o C to 80o C
- Tack free time: 9 minutes to13 minutes
- Cutting time: 60 minutes
- Foam yield: 6 lt/100 ml
- Adhesive strength PVC to PVC: >100 KPA
- Aluminium to aluminium: > 80KPA
- Elongation at break: 8% to 20%
- Compression strength at 10% compression: 35 KPA to 100 KPA
- Shear strength: 22 KPA to 50 KPA
- Water absorption by volume: 0.03%
- Thermo conductivity: < 0.035 Kcal/mHo C
- Closed cells: 60% to 70%
- Average burning time: 60 seconds
- Average burning scope: 25 mm
WD 40

Applications in auto industry. Rust protection in component manufacturing and servicing in ggarage applicationsin auto industry. Rust protection in component manufacturing and servicing in garages. Abrasion protection. Structural Reinforcement. Repairs in hard to reach areas. Underwater repairs. Electrical conduit/cable repairs

WD 40
- Protect against rust & corrosion
- Air Humidity cure mechanism
- Safe for drinking water and resistant to most of chemicals
- Temperature resistance upto 200°C
- Suitable for Liquid or Gas pipelines
- Permanent repair or extend service life of pipes
- Ideal for pipe reinforcement and corrosion protection
- Appearance Aerosol-Aerosolized Liquid, Bulk-Liquid
WRAP SEAL

Repairing pipes and active leaks. Repairing metal and plastic pipes carrying water, acids alkalis, hydrocarbons, fuels, gases, slurries and other chemicals. Sealant for joints and hazardous material spill control. Reinforcement of thinning walls and protection from corrosion. Repairing under water pipe. Repairing electrical conduits and cables. Wrap Seal PLUS Fiberglass Repair Tape for straight section, elbows, tee-joints, reducers, flanges, valves. Suitable for pipeline with diameter up to 60” (1524 mm), temperature up to 280 °C (536 °F)

WRAP SEAL
- Applicable to pipes up to 18” (457mm) diameter
- Repairs T-joint, elbow joint, valve thread, valve body
- Withstand pressure up to 400 psi (28 kg/cm²)
- Withstand temperature up to 200°C (392°F)
- Safe for drinking water and resistant to most chemicals
- Reinforce and strengthen pipe after repair
- Permanent repair and extend service life of pipes
- Pressure Test:
- ½ steel pipe with 1/8 hole with WRAPSEAL without SEAL STIC: 1,500 PSI
- ½ steel pipe with 1/8 hole with WRAPSEAL with SEAL STIC: 4,000 PSI
- ½ steel pipe with ½ hole with WRAPSEAL without SEAL STIC: 600 PSI
- Tensile strength: 3,920 PSI
- Bond strength: 230 PSI
- Tensile elongation: 1.2% ± 0.7%
- Elongation to break: 400%
- Compression strength: 13,750 PSI ± 530 PSI
- Yield strength: 2,260 PSI
- Toughness: 35,000 PSI
- Shrink force: 38 PSI
- Volume resistivity: 14/cm
- Heat shock: No visual crashing, flowing or dripping
- Adhesive peel to steel, PE and Epoxy: 10 lbs per linear inch
- Impact strength: 30 inch/lbs
- Moisture vapours transmission: 0.1g (per 24 hours per 100 inch2)
- Dielectric breakdown voltage: 20kV
- Cured hardness (Shore D): 82
ZORRIK 101

Mixing ratio 2 parts of A to 1 part of B, by weight. Stir each component independently. Mix for 3 minutes to homogenous. Apply using brush, roller or spray

ZORRIK 101
- 100% Solids
- High Dielectric strength and Breakdown voltage
- Self-levelling
- Non-sagging
- Non Toxic
- Chemical composition: High build Epoxy
- Physical: White viscous liquid
- Certification: ERDA Certificate – Electrical Insulation
- Food grade certificate
- Salt Spray Test
- Global Migration Test
ZORRIK 1411

Surface preparation followed by application either by Brush or Spray

ZORRIK 1411
- Excellent bond strength, with concrete failure in pull-off test
- Low viscous
- Slow curing
- Bonds tenaciously to become an integral part of the floor
- Chemical composition: Epoxy polyamidoamined
- Physical: Clear Gloss
ZORRIK 201

Mix Part A and B using slow speed. Apply by airless spray or brush after first coat. For concrete repair, fair with 1 part Zorrik 201 + 1.5 parts filler then apply

ZORRIK 201
- 100% solids
- Superior Novolac system
- Resistance to chemicals and erosion
- Chemical composition: High build Novolac Epoxy
- Physical: White viscous liquid
- Certification: Food grade certificate
- Salt Spray Test
- Pull out adhesion
ZORRIK 301

Emergency leakages repair of BF water cooling jacket and water pipes. Oil leakages in Transformers, Pipe line, elbows and gear box flanges. Leakage arresting of coal mill gear box flanges. Filling of pitting holes & stripped threads

ZORRIK 301
- Cures rapidly in 5 minutes at room temperature - Saves downtime
- Non Sag, No Shrink
- Cures to metal luster finish
- Excellent adhesion to metals like steel, cast iron, stainless steel, concrete, copper, aluminium, and bonze
- Appearance: Steel Paste
- Components: Two Component- Mixing
- Cure: Room temperature
- Mix Ratio by Volume – Resin : Hardener:: 1:1
- Mix Ration by Weight- Resin: Hardener:: 100:56
- Density @ 30 °C : 2.2-2.5 g/ml
- Coverage on mixing: 800 cm² @ 6 mm thick per 1 kg kit
- Operating Temperature: -30 °C to 100 °C
ZORRIK 311

Restoring tolerance to worn shafts. Bearing seats and housings. Motor end covers. Key ways. Thinned pipes, tubes sections. Engine blocks. Pump casings and impeller. Rebuilding of water, coal slurry pump casings

ZORRIK 311
- Contains no iron or steel fillers
- Corrosion eliminated due to high Ferro-silicon content during service time
- Epoxy resin base – Excellent adhesion to steel and cast iron
- Superior machining finished surface
- Tolerance - Facilitates fine tolerance limits
- Excellent resistance to a variety of chemicals
- Appearance ( Mix): Grey paste
- Components : Two Component- Mixing
- Cure : Room temperature
- Mix Ratio by Volume – Resin : Hardener:: 4:1
- Mix Ration by Weight- Resin: Hardener:: 7:1
- Coverage: 575 cm² @ 6 mm thickness per 1 kg kit
- Operating Temperature : -30 °C to 120 °C
ZORRIK 411

Mix part A and Part B then Brushable application on the surface

ZORRIK 411
- Smooth brushable
- Reduce downtime
- Adhesion to metals
- Ceramic and
- Silicon carbide filled
- Chemical composition : Epoxy Composite
- Physical: Grey flowable liquid
ZORRIK 99

Electrical and mechanical equipments, motors, switches and switch gears, fuse boxes, capacitors, transformers, connectors, ignition equipments, test instruments, rocker / push-pull switches, relays, circuit breakers, transformers, switchgears, bus bars, Terminals, Transformers, generators, control instruments, communication assemblies, starters, solenoids etc

ZORRIK 99
- Removes surface moisture effectively
- Appearance : Clear
ZORRIK Cu 7618

Brushable / Spatula

ZORRIK Cu 7618
- Prevents seizure against corrosion and temperature
- Works very effective in humid and corrosive environments
- Reduces maintenance downtime
- Chemically inert and seawater resistant
- Chemical composition: Inorganic Binder Molybdenum base
- Physical: Grease (Paste)
ZORRIK QD ELECTRONIC CONTACT CLEANER

To remove dust, dirt, oil, grease, flux, and other grim from electronic printed circuit boards, electronic parts, potentiometers, test instruments, rocker/push-pull switches, relays, circuit breakers, transformers, switchgears, controll instruments, communication assemblies & other sensitive electronic components

ZORRIK QD ELECTRONIC CONTACT CLEANER
- Fast Evaporating
- Appearance : Colourless to pale yellow liquid
ZORRIK Rust Cleaner 100

Clean the surface for any dirt or dust then apply the product via spraying

ZORRIK Rust Cleaner 100
- Ceases squeaks by penetrating & lubricating the innermost parts which are normally inaccessible
- Replaces moisture and shields metals, releases rusty accessories
- Cleans away light soils, grease and adhesives
- Easy to apply
- Chemical composition: Blend of solvents and lubricating Oil
- Physical: Clear and transparent
ZORRIK SL 14340 1mm CA

Surface prep followed by Primer/ Screed and then Lay the mixture to the desired thickness. De-aerate by using spike rollers

ZORRIK SL 14340 1mm CA
- Excellent adhesion
- Excellent self-levelling properties
- Good chemical resistance
- Good abrasion resistance
- Cost-effective
- Chemical composition: Epoxy Cyclo aliphatic amine
- Physical: Desired shade and smooth glossy finish
ZORRIK HS 1421

Add Zorrik Water Based Cleaner – 200 to water for preparation of the solution. Concentration and processing time depend on contaminants, method, and geometry. Concentration control by titration recommended as removed oil can modify reading if checked with refractometer

ZORRIK HS 1421
- Remove soil, swarf, rust preventive film and smut
- Low foaming and withstand 200 bar spray pressure
- Good short term rust protection, if water rinses not given
- De-emulsify oil; gives good sump life
- Free from low molecular weight volatile solvent
- Formulated using non-toxic ingredients
- Can be used for all food and pharma applications
- Physical: Clear to slight haze liquid

PIDILITE

Fevicol ANR 243

Fevicol ANR 270

Fevicol ANR 574

Fevicol ANR 638

Fevikwik 203

Fevikwik 702

Feviseal Neutral Pro

M Seal Epoxy

M Seal Red RTV Silicone Sealant Gasket Maker

PIDISEAL 3P

RUSTOLENE

SYNTHEIC RUBBER AHESIVE

USPRO

WD 40

WRAP SEAL

ZORRIK 101

ZORRIK 1411

ZORRIK 201

ZORRIK 301

ZORRIK 311

ZORRIK 411

ZORRIK 99

ZORRIK Cu 7618

ZORRIK QD ELECTRONIC CONTACT CLEANER

ZORRIK Rust Cleaner 100

ZORRIK SL 14340 1mm CA

ZORRIK HS 1421